QuTS hero h5.1.1.2488 build 20230812 released

Zitat von qnap.com

QuTS hero h5.1.1.2488 build 20230812

2023-08-21

Applicable Models

• TS-h2490FU/TS-h1090FU
• TS-h1290FX
• TDS-h2489FU

Show more

Important Notes

• QuTS hero does not support downgrading from h5.1.x to h5.0.1 or earlier.
• To run Virtualization Station on QuTS hero h5.1.1, version 3.6.49 or later is required. If you are using an earlier version of Virtualization Station, please update Virtualization Station before updating QuTS hero to h5.1.1.
• In QuTS hero h5.0.1 or earlier, users can no longer create new VJBOD disks from a remote NAS if the remote NAS is running QuTS hero h5.1.0 or later. If there are existing VJBOD disks connections to the remote NAS before it is updated to QuTS hero h5.1.0 or later, these VJBOD disks are unaffected and remain operational after the update. In QuTS hero h5.1.0 or later, users can still create VJBOD disks from a remote NAS running QuTS hero h5.0.1 or earlier.
• Removed support for CO Video.

Security Updates

• Applied multiple security updates to further enhance system security.

New Features

• For details on new features in QuTS hero h5.1, please visit https://www.qnap.com/go/releas…hero/h5.1.0.2466/20230721

Enhancements

Control Panel

• System Status now displays the statuses of all power supply units on all external storage enclosures, regardless of whether the NAS supports redundant power supply.

Initialization

• Users can now configure firmware update settings in the Smart Installation Guide during QTS initialization.

Network & Virtual Switch

• Optimized the switch configuration UI for QGD rackmount series running QuTS hero, with added support for models that do not support PoE.

Storage & Snapshots

• Upgraded the IronWolf Health Management (IHM) utility to implement support for the latest ST drive models as well as future models within the IHM-supported range.
• Upgraded the Western Digital Device Analytics (WDDA) utility to update the generated recommended actions.

Fixed Issues

• Fixed an issue where Dashboard > Resource Monitor would sometimes display the wrong transfer speed unit when the interface language was set to Simplified Chinese.
• Improved MariaDB support for all time zones.
• Improved the display ratio of the desktop wallpaper.
• Improved the login process.
• Fixed an issue in File Station where folders would be incorrectly sorted if one or more of the folder names included certain special characters.
• Fixed an issue in File Station where if the NAS time was ahead of the client time, uploading a file would cause Background Tasks to incorrectly display a "Failed" message until the upload was complete.
• Fixed an issue in File Station where some action options were missing when right-clicking XLSM files.
• Fixed an issue where if "Always keep SMB file attributes" was enabled in File Station > More > Settings > File Operations, and the user had uploaded a file to the NAS via SMB, the file might get stuck in "Preparing" status when copying the file to another folder in File Station.
• Fixed an issue where some files could not be recovered when recovering a folder with a large number of files from a recycle bin.
• Fixed an issue where some files could not be transferred when dragging and dropping a folder with a large number of files.
• Fixed an issue where under certain circumstances, File Station would be stuck at "Searching..." after trying to search files by keyword.
• Fixed an issue where when two users were simultaneously logged in to the same NAS and tried to access the same folder, an unexpected error message might appear.
• Improved the speed of downloading through a share link after having previously transferred a massive amount of data through the same share link.
• Fixed an issue where Notification Center could not send notification emails when notification rules were triggered.
• Resolved an issue where trying to add a QNAP ID that already existed in myQNAPcloud > Access Control > Custom Settings would incorrectly trigger an "Unknown error" message.
• Fixed an issue where users could not configure a service to use a port number already reserved for another service even though the two services used different communication protocols (e.g., TCP and UDP).
• Fixed an issue where when the system default gateway had an IPv6 address and was connected to a virtual switch, the myQNAPcloud > DDNS page did not display the IPv6 address when My DDNS was enabled.
• Resolved an issue in Network & Virtual Switch where users would encounter an unexpected error when trying to add a static route using a VPN interface.
• Resolved an issue where iSCSI & Fibre Channel would stop responding for some users after trying to open the application.
• Fixed an issue in Notification Center where the system would continue to send email notifications to a recipient who had been removed from a notification rule.
• Resolved an issue where the system would incorrectly display an "Unable to send firmware update notifications" message after creating a notification rule for firmware updates.
• Improved the user and group permission mechanism for shared folders.
• Fixed an issue in Qsirch where users could not search NAS files in Finder in macOS Ventura.
• Improved the speed of Veeam backup jobs in QuObjects when the source data includes WORM folders and files.
• Fixed an issue where users could not access folders via Samba if their username contained certain special characters.
• Fixed an issue where some users would encounter certain unexpected storage issues when reinserting a disk after a firmware update.
• Fixed an issue where users could not fully delete a shared folder if the shared folder contained a very large number of files.
• Fixed an issue where users could not import a storage pool under certain conditions.
• Resolved an issue where properly shutting down the NAS caused the S.M.A.R.T. attribute "Power-Off Retract Count" in HDDs to unexpectedly increase in value.
• Fixed a rare issue where the system could not successfully start up on TVS-hx74 series NAS devices.
• Fixed an issue where the NAS would restart unexpectedly while using certain third-party apps to access the NAS via NFS.

Known Issues

• After upgrading a Mac computer with an M1 or M2 CPU to macOS 12.6.1, users can no longer connect QNAP NAS devices to the Mac computer via Thunderbolt.

Alles anzeigen