Hallo Leute,
meine TS-253 Pro hatte sich im laufenden Betrieb auf der aktuellen 4.2 1118 auf einmal einen sporadischen Reboot und sagte mir im Log danach das die Konfiguration zurückgesetzt wurde (jedoch waren meine iSCSI Lun´s alle noch erreichbar) seitdem macht die Box alle 4-5 min Reboots.
Ok dachte ich mir spielst halt das Testimage welches im qnap wiki (Recovery) zur x53 Serie verlinkt ist, kopierst mittels dd das image auf den USB-DOM und updatest die Box mittels Qfinder wieder.
Nun nach mehrtätgigem rumprobieren (auch versch. QTS-Versionen) und keinem angeschlossenen Laufwerk, kriege ich es nicht hin die Box von diesen Reboots abzuhalten. (Auch ist die Mail an den HelpDesk schon seit 3 Tagen raus - bisher ohne Antwort..)
nach studieren des Kernel-Logs fiel mir auf das das Testimage keine Reboots erzeugt jedoch alle Fullimages von QTS 4.1 sowie 4.2. bei der 20150925er schreibt der Kernel jedoch folgenden segfault raus :
[ 8.934421] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 8.939666] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 8.947203] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 8.947243] xhci_hcd 0000:00:14.0: irq 106 for MSI/MSI-X
[ 8.947560] hub 1-0:1.0: USB hub found
[ 8.951335] hub 1-0:1.0: 6 ports detected
[ 8.956210] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 8.961446] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 8.969090] hub 2-0:1.0: USB hub found
[ 8.972861] hub 2-0:1.0: 1 port detected
[ 8.983865] usbcore: registered new interface driver usb-storage
[ 8.996359] mpt2sas version 16.100.00.00 loaded
[ 9.003386] Intel(R) Gigabit Ethernet Network Driver - version 5.1.2
[ 9.009757] Copyright (c) 2007-2013 Intel Corporation.
[ 9.014946] pcieport 0000:00:1c.2: driver skip pci_set_master, fix it!
[ 9.022067] igb 0000:03:00.0: irq 107 for MSI/MSI-X
[ 9.022086] igb 0000:03:00.0: irq 108 for MSI/MSI-X
[ 9.051289] igb 0000:03:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 9.058164] igb 0000:03:00.0: eth0: (PCIe:2.5GT/s:Width x1)
[ 9.063822] igb 0000:03:00.0: eth0: MAC:
[ 9.067831] 00:08:9b:f2:15:5e
[ 9.070917] igb 0000:03:00.0: eth0: PBA No: 001300-000
[ 9.076084] igb 0000:03:00.0: LRO is disabled
[ 9.080529] igb 0000:03:00.0: Using MSI-X interrupts. 1 rx queue(s), 1 tx queue(s)
[ 9.088129] pcieport 0000:00:1c.3: driver skip pci_set_master, fix it!
[ 9.095222] igb 0000:04:00.0: irq 109 for MSI/MSI-X
[ 9.095241] igb 0000:04:00.0: irq 110 for MSI/MSI-X
[ 9.124274] igb 0000:04:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 9.131150] igb 0000:04:00.0: eth1: (PCIe:2.5GT/s:Width x1)
[ 9.136806] igb 0000:04:00.0: eth1: MAC:
[ 9.140814] 00:08:9b:f2:15:5f
[ 9.143901] igb 0000:04:00.0: eth1: PBA No: 001300-000
[ 9.149067] igb 0000:04:00.0: LRO is disabled
[ 9.153513] igb 0000:04:00.0: Using MSI-X interrupts. 1 rx queue(s), 1 tx queue(s)
[ 9.202380] flashcache: flashcache-3.1.1-3 initialized
[ 9.212918] drbd: events: mcg drbd: 7
[ 9.220978] drbd: initialized. Version: 8.4.5 (api:1/proto:86-101)
[ 9.227162] drbd: GIT-hash: 1d360bde0e095d495786eaeb2a1ac76888e4db96 build by @NasX86-12, 2015-09-25 05:11:13
[ 9.237097] drbd: registered as block device major 147
[ 9.340654] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 9.384347] hub 1-1:1.0: USB hub found
[ 9.388299] hub 1-1:1.0: 4 ports detected
[ 9.546635] usb 1-4: new high-speed USB device number 3 using xhci_hcd
[ 9.565396] usb 1-4: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
[ 9.574271] usb 1-4: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
[ 9.583307] usb-storage 1-4:1.0: USB Mass Storage device detected
[ 9.589503] scsi2 : usb-storage 1-4:1.0
[ 9.694735] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 9.714940] hub 2-1:1.0: USB hub found
[ 9.718854] hub 2-1:1.0: 4 ports detected
[ 9.805731] usb 1-1.2: new full-speed USB device number 4 using xhci_hcd
[ 9.831797] input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input6
[ 9.844330] hid-generic 0003:045E:0745.0001: input: USB HID v1.11 Keyboard [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:14.0-1.2/input0
[ 9.863728] input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input7
[ 9.876283] hid-generic 0003:045E:0745.0002: input: USB HID v1.11 Mouse [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:14.0-1.2/input1
[ 9.905308] input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/1-1.2:1.2/input/input8
[ 9.917940] hid-generic 0003:045E:0745.0003: input,hiddev0: USB HID v1.11 Device [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:14.0-1.2/input2
[ 10.595284] scsi 2:0:0:0: Direct-Access ADATA IUM01-512MFHS 0100 PQ: 0 ANSI: 0 CCS
[ 10.603815] Check proc_name[usb-storage].
[ 10.607981] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 10.613525] sd 2:0:0:0: [sda] 1007616 512-byte logical blocks: (515 MB/492 MiB)
[ 10.621306] sd 2:0:0:0: [sda] Write Protect is off
[ 10.626110] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 10.626577] sd 2:0:0:0: [sda] No Caching mode page found
[ 10.631891] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 10.639450] sd 2:0:0:0: [sda] No Caching mode page found
[ 10.644762] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 10.652815] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 10.659158] sd 2:0:0:0: [sda] No Caching mode page found
[ 10.664475] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 10.670570] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 31.023557] usbcore: registered new interface driver usbserial
[ 31.031026] usbcore: registered new interface driver pl2303
[ 31.036631] usbserial: USB Serial support registered for pl2303
[ 31.044140] jnl: driver (lke_9.2.0 QNAP, LBD=OFF) loaded at ffffffffa01d5000
[ 31.053210] ufsd: module license 'Commercial product' taints kernel.
[ 31.059579] Disabling lock debugging due to kernel taint
[ 31.066156] ufsd: driver (lke_9.2.0 QNAP, build_host("NasX86-12"), acl, ioctl, bdi, sd2(0), fua, bz, rsrc) loaded at ffffffffa01e0000
[ 31.066156] NTFS support included
[ 31.066156] Hfs+/HfsJ support included
[ 31.066156] optimized: speed
[ 31.066156] Build_for__QNAP_TS-451_k3.12.6_2014-12-11_lke_9.2.0_r245986_b11
[ 31.066156]
[ 31.205757] udevd (223): /proc/223/oom_adj is deprecated, please use /proc/223/oom_score_adj instead.
[ 31.214989] udev: starting version 140
[ 43.296006] cryptodev: driver 0.9 loaded.
[ 43.308693] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 43.314333] iTCO_wdt: Found a Baytrail SoC TCO device (Version=4, TCOBASE=0x0460)
[ 43.321988] iTCO_wdt: initialized. heartbeat=120 sec (nowayout=0)
[ 43.341200] fnotify: Load file notify kernel module.
[ 43.346279] fnotify: Launch the fnotify thread: 18446612134270284032
[ 43.362345] iTCO_wdt: Timeout value (heartbeat) is set to 120
[ 44.388800] usbcore: registered new interface driver snd-usb-audio
[ 44.396448] usbcore: registered new interface driver snd-usb-caiaq
[ 44.408636] usbcore: registered new interface driver uvcvideo
[ 44.414398] USB Video Class driver (1.1.1)
[ 44.459403] 8021q: 802.1Q VLAN Support v1.8
[ 66.456018] 8021q: adding VLAN 0 to HW filter on device eth0
[ 66.676999] 8021q: adding VLAN 0 to HW filter on device eth1
[ 69.320456] igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 74.413407] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 74.435529] Bridge firewalling registered
[ 74.484130] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 74.491278] bonding: MII link monitoring set to 100 ms
[ 97.167693] [fintek_proc_write] cir enable
[ 97.171827] fintek_cir: fintek-cir: Dump CIR logical device registers:
[ 97.178356] fintek_cir: * CR CIR BASE ADDR: 0xffff
[ 97.183231] fintek_cir: * CR CIR IRQ NUM: 0xff
[ 97.187932] fintek_cir: fintek-cir: Dump CIR registers:
[ 97.193154] fintek_cir: * STATUS: 0xff
[ 97.197334] fintek_cir: * CONTROL: 0xff
[ 97.201516] fintek_cir: * RX_DATA: 0xff
[ 97.205699] fintek_cir: * TX_CONTROL: 0xff
[ 97.209878] fintek_cir: * TX_DATA: 0xff
[ 234.498402] rule type=2, num=0
[ 234.526764] hal_enc_reset[741]: segfault at 46 ip 00000000f71d94ad sp 00000000f3eb8060 error 4 in libc-2.6.1.so[f7183000+12d000]
Alles anzeigen
So nun bin ich mit meinem Latein am Ende... und frage euch deshalb mal dazu was hier den Fehler verursachen könnte da ja unter dem Testimage auch ein Speichertest und Stresstest keinen Absturz oder Reboot hervorruft gehe ich mal davon aus das die Hardware in Ordnung ist (oder auch nicht 
)
Bitte euch um Hilfe da Qnap anscheinend zu beschäftigt ist sich diesem Problem anzunehmen, danke vorerst mal.... :thumb:
