Hallo
ich habe heute mein TS-859Pro+ geupdatet hat auch alles Problemlos geklappt (von 3.7.1 auf 3.7.2)
nur dann waren die Netzwerk Freigaben nicht mehr zu erreichen
unter Datenträgerverwaltung wird folgendes angezeigt:
Dateisystem = Unbekannt
Gesamtgröße = --
Freie Größe = --
Staus = Entladen
im Systemprotokolle:
[RAID5 Disk Volume: Drive 1 2 3 4 5 6 7 8] The file system is not clean. It is suggested that you run "check disk".
Mit "dmesg" in der Konsole wird das angezeigt
[~] # dmesg
3 stopped.
[ 51.669082] md: bind<sdb4>
[ 51.678607] md: bind<sdc4>
[ 51.679418] md: bind<sdd4>
[ 51.687396] md: bind<sde4>
[ 51.690736] md: bind<sdf4>
[ 51.698759] md: bind<sdg4>
[ 51.706955] md: bind<sdh4>
[ 51.712911] md: bind<sda4>
[ 51.714602] raid1: raid set md13 active with 8 out of 8 mirrors
[ 51.718449] md13: bitmap initialized from disk: read 4/4 pages, set 0 bits
[ 51.718556] created bitmap (57 pages) for device md13
[ 51.755337] md13: detected capacity change from 0 to 469893120
[ 51.759577] md13: unknown partition table
[ 53.358623] kjournald starting. Commit interval 5 seconds
[ 53.464236] EXT3-fs (md9): using internal journal
[ 53.464422] EXT3-fs (md9): mounted filesystem with writeback data mode
[ 71.995483] kjournald starting. Commit interval 5 seconds
[ 72.077613] EXT3-fs (md9): using internal journal
[ 72.077789] EXT3-fs (md9): mounted filesystem with writeback data mode
[ 99.650974] kjournald starting. Commit interval 5 seconds
[ 99.860664] EXT3-fs (md13): using internal journal
[ 99.860840] EXT3-fs (md13): mounted filesystem with writeback data mode
[ 110.890111] cryptodev: driver 0.9 loaded.
[ 110.913307] usbcore: registered new interface driver hiddev
[ 110.996857] generic-usb 0003:051D:0002.0001: hiddev96: USB HID v1.00 Device [American Power Conversion Back-UPS RS 550GI FW:857.L1 .I USB FW:L1 ] on usb-0000:00:1d.1-1/input0
[ 110.997451] usbcore: registered new interface driver usbhid
[ 110.997573] usbhid: USB HID core driver
[ 111.001912] Register ICH/PCH RTC driver.
[ 111.008527] iTCO_vendor_support: vendor-support=0
[ 111.014539] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 111.019621] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0860)
[ 111.020200] iTCO_wdt: initialized. heartbeat=120 sec (nowayout=0)
[ 111.028801] usbcore: registered new interface driver usblp
[ 111.036045] ufsd: module license 'Commercial product' taints kernel.
[ 111.036192] Disabling lock debugging due to kernel taint
[ 111.059584] ufsd: driver 8.3 (Jun 15 2012 04:28:54) with acl LBD=OFF with ioctl loaded at ffffffffa00c8000
[ 111.059589] NTFS read/write support included
[ 111.059592] Hfs+/HfsX read/write support included
[ 111.084595] fnotify: Load file notify kernel module.
[ 111.085059] fnotify: Global_Private_Data_List_Init()
[ 111.085219] fnotify: Launch the fnotify thread: 2728
[ 111.087438] fnotify: The fnotify thread starts...
[ 112.150449] usbcore: registered new interface driver snd-usb-audio
[ 112.159004] usbcore: registered new interface driver snd-usb-caiaq
[ 112.191435] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 112.191553] pci 0000:00:02.0: setting latency timer to 64
[ 112.205292] alloc irq_desc for 35 on node -1
[ 112.205300] alloc kstat_irqs on node -1
[ 112.205314] pci 0000:00:02.0: irq 35 for MSI/MSI-X
[ 112.205648] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 112.229690] Linux video capture interface: v2.00
[ 112.250450] usbcore: registered new interface driver uvcvideo
[ 112.250581] USB Video Class driver (v0.1.0)
[ 112.396877] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 112.397000] All bugs added by David S. Miller <davem@redhat.com>
[ 114.249299] kjournald starting. Commit interval 5 seconds
[ 114.257200] EXT3-fs (md9): using internal journal
[ 114.257379] EXT3-fs (md9): mounted filesystem with writeback data mode
[ 115.679107] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 115.782134] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 116.409378] active port 0 :139
[ 116.409474] active port 1 :445
[ 116.409564] active port 2 :20
[ 119.299076] md: bind<sda2>
[ 119.300675] raid1: raid set md8 active with 1 out of 1 mirrors
[ 119.300816] md8: detected capacity change from 0 to 542769152
[ 120.305707] md8: unknown partition table
[ 122.410190] Adding 530040k swap on /dev/md8. Priority:-1 extents:1 across:530040k
[ 126.038175] md: bind<sdb2>
[ 126.053213] RAID1 conf printout:
[ 126.053329] --- wd:1 rd:2
[ 126.053439] disk 0, wo:0, o:1, dev:sda2
[ 126.053549] disk 1, wo:1, o:1, dev:sdb2
[ 126.053760] md: recovery of RAID array md8
[ 126.053876] md: minimum _guaranteed_ speed: 5000 KB/sec/disk.
[ 126.053995] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 126.054193] md: using 128k window, over a total of 530048 blocks.
[ 128.278733] md: bind<sdc2>
[ 129.605557] md: md0 stopped.
[ 129.617061] md: md0 stopped.
[ 129.834239] md: bind<sdb3>
[ 129.834527] md: bind<sdc3>
[ 129.834780] md: bind<sdd3>
[ 129.835101] md: bind<sde3>
[ 129.835418] md: bind<sdf3>
[ 129.835735] md: bind<sdg3>
[ 129.836041] md: bind<sdh3>
[ 129.836289] md: bind<sda3>
[ 129.837800] raid5: device sda3 operational as raid disk 0
[ 129.837907] raid5: device sdh3 operational as raid disk 7
[ 129.838006] raid5: device sdg3 operational as raid disk 6
[ 129.838105] raid5: device sdf3 operational as raid disk 5
[ 129.838213] raid5: device sde3 operational as raid disk 4
[ 129.838317] raid5: device sdd3 operational as raid disk 3
[ 129.838429] raid5: device sdc3 operational as raid disk 2
[ 129.838530] raid5: device sdb3 operational as raid disk 1
[ 129.855054] raid5: allocated 135840kB for md0
[ 129.855296] 0: w=1 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855419] 7: w=2 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855519] 6: w=3 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855616] 5: w=4 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855714] 4: w=5 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855812] 3: w=6 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.855911] 2: w=7 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.856010] 1: w=8 pa=0 pr=8 m=1 a=2 r=8 op1=0 op2=0
[ 129.856107] raid5: raid level 5 set md0 active with 8 out of 8 devices, algorithm 2
[ 129.856266] RAID5 conf printout:
[ 129.856357] --- rd:8 wd:8
[ 129.856459] disk 0, o:1, dev:sda3
[ 129.856551] disk 1, o:1, dev:sdb3
[ 129.856643] disk 2, o:1, dev:sdc3
[ 129.856734] disk 3, o:1, dev:sdd3
[ 129.856826] disk 4, o:1, dev:sde3
[ 129.856917] disk 5, o:1, dev:sdf3
[ 129.857009] disk 6, o:1, dev:sdg3
[ 129.857100] disk 7, o:1, dev:sdh3
[ 129.857281] md0: detected capacity change from 0 to 20992903938048
[ 130.396574] md: bind<sdd2>
[ 131.068222] md0: unknown partition table
[ 132.649408] md: bind<sde2>
[ 134.821468] md: bind<sdf2>
[ 135.357076] EXT4-fs (md0): ext4_check_descriptors: Checksum for group 64320 failed (26657!=30001)
[ 135.357309] EXT4-fs (md0): group descriptors corrupted!
[ 136.956460] md: bind<sdg2>
[ 139.214908] md: bind<sdh2>
[ 151.119108] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 151.154106] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 152.463750] md: md8: recovery done.
[ 152.619863] RAID1 conf printout:
[ 152.619970] --- wd:2 rd:2
[ 152.620079] disk 0, wo:0, o:1, dev:sda2
[ 152.620180] disk 1, wo:0, o:1, dev:sdb2
[ 161.877234] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 177.482968] active port 0 :139
[ 177.483070] active port 1 :445
[ 177.483160] active port 2 :20
[ 177.641864] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
[ 206.810513] rule type=2, num=0
[ 208.980556] EXT4-fs (sdu1): mounted filesystem with ordered data mode
[ 211.642499] Loading iSCSI transport class v2.0-871.
[ 211.690508] iscsi: registered transport (tcp)
[ 220.505563] active port 0 :139
[ 220.505662] active port 1 :445
[ 220.505803] active port 2 :20
[ 2574.693906] active port 0 :139
[ 2574.693973] active port 1 :445
[ 2574.694040] active port 2 :20
[~] #
Alles anzeigen
verbaut sind 8 x Seagate ST3000DM001
Die alte Firmware (3.7.1) wurde auch schon ohne Erfolg eingespielt
Kann ich jetzt noch was tun um Zugiff auf die Daten zu bekommen?
