[TS-509 Pro] - [HDD SMART] Aborted by host

    Hallo,
    besitze ein TS-509 Pro NAS mit 3 eingebauten Platten, HDD 1+2 als Raid1, HDD 3 als Einzeldisk.


    Vor ca. 1 1/2 Wochen hat der HDD SMART meines NAS auf HDD 1 nach einem umfangreichen Test die Meldung "Full Test result: Completed: read failure" gebracht, nach einem ausführlichen Festplattentest dann die Meldung "Bad Blocks Scan completed. 134 bad block(s) found". Aufgrund dessen habe ich sicherheitshalber ein Backup der Daten auf die HDD 3 gemacht und anschließend die Platte 1 mit einer neuen getauscht. Nach ca. 3 Stunden war das Rebuilding fertig.


    Code
    246,"0","2009-12-25","03:40:23","System","127.0.0.1","localhost","[HDD SMART] HDD 3 Full Test result: Completed without error."245,"0","2009-12-25","03:40:22","System","127.0.0.1","localhost","[HDD SMART] HDD 1 Full Test result: Completed without error."244,"0","2009-12-25","03:38:52","System","127.0.0.1","localhost","[HDD SMART] HDD 2 Full Test result: Completed without error."243,"0","2009-12-25","02:02:34","System","192.168.2.21","localhost","[HDD SMART] HDD 3 Full Test started."242,"0","2009-12-25","02:02:28","System","192.168.2.21","localhost","[HDD SMART] HDD 2 Full Test started."241,"0","2009-12-25","02:02:18","System","192.168.2.21","localhost","[HDD SMART] HDD 1 Full Test started."240,"0","2009-12-25","02:01:26","System","127.0.0.1","localhost","[Drive 1] Bad Blocks Scan completed."239,"0","2009-12-25","02:01:26","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] Drive 1 added into volume 4."238,"0","2009-12-25","00:11:32","System","127.0.0.1","localhost","[Drive 1] Start scanning bad blocks."237,"0","2009-12-25","00:10:07","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] Rebuilding completed."236,"0","2009-12-24","20:54:25","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] Start rebuilding."235,"0","2009-12-24","20:54:12","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] Drive 1 added into volume 4."234,"0","2009-12-24","20:53:48","System","127.0.0.1","localhost","Drive 1 plugged in."233,"1","2009-12-24","20:50:38","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] RAID device in degraded mode."232,"0","2009-12-24","20:50:38","System","127.0.0.1","localhost","[Mirror Disk Volume: Drive 1 2] Drive 1 removed."231,"2","2009-12-24","20:50:28","System","127.0.0.1","localhost","Drive 1 plugged out."


    Im NAS habe ich eingestellt, dass alle 3 Tage ein ausführlicher SMART-Test um 3.00 Uhr nachts durchgeführt werden soll.


    Nun zu meinem Problem:


    Seit dem Tausch der Platte bricht der SMART-Test, wenn er automatisch gestartet wird, nach wenigen Minuten mit der folgenden Meldung ab:


    Code
    260,"1","2009-12-27","03:12:37","System","127.0.0.1","localhost","[HDD SMART] HDD 3 Full Test result: Aborted by host."
259,"1","2009-12-27","03:12:36","System","127.0.0.1","localhost","[HDD SMART] HDD 2 Full Test result: Aborted by host."
258,"1","2009-12-27","03:12:25","System","127.0.0.1","localhost","[HDD SMART] HDD 1 Full Test result: Aborted by host."
257,"0","2009-12-27","03:00:13","System","127.0.0.1","localhost","[HDD SMART] HDD 2 Full Test started."
256,"0","2009-12-27","03:00:12","System","127.0.0.1","localhost","[HDD SMART] HDD 1 Full Test started."
255,"0","2009-12-27","03:00:11","System","127.0.0.1","localhost","[HDD SMART] HDD 3 Full Test started."


    Wenn der Test "per Hand", also manuell gestartet wird, läuft alles problemlos durch und es erscheint auch keine Fehlermeldung. Hat evtl. jemand das gleiche Problem oder kann helfen?


    Für jeden Hinweis wäre ich dankbar ;)

    Hallo Christian,
    danke für die schnelle Antwort!


    Ich habe das Häkchen für die Prüfung rausgenommen und wieder reingemacht.. leider das selbe Problem:


    Code
    2010-01-04	46	03:12:42	System	127.0.0.1	localhost	[HDD SMART] HDD 3 Full Test result: Aborted by host.	
2010-01-04	45	03:12:31	System	127.0.0.1	localhost	[HDD SMART] HDD 2 Full Test result: Aborted by host.
2010-01-04	44	03:00:21	System	127.0.0.1	localhost	[HDD SMART] HDD 1 Full Test started.
2010-01-04	43	03:00:21	System	127.0.0.1	localhost	[HDD SMART] HDD 2 Full Test started.
2010-01-04	42	03:00:20	System	127.0.0.1	localhost	[HDD SMART] HDD 3 Full Test started.
2010-01-04	41	03:00:20	System	127.0.0.1	localhost	[HDD SMART] HDD 1 Full Test result: Aborted by host.

    Hallo,


    ich denke das Log sagt alles.. ich habe die geplante Prüfung mal zum Testen auf 11.00 Uhr verschoben, der Test startet und läuft problemlos durch. Anschließend hab ich die Zeit auf 2.30 Uhr nachts abgeändert, nun würde aber angeblich der Test auf HDD1 sofort und HDD3 in 10 Minuten durchgelaufen sein und auf HDD2 bricht er wieder ab?!?!


    Kann es auch evtl. an der neuen Firmware liegen??